| Journal "Tekhnologiya Mashinostroeniya" | ISSN 1562-322X |
| Contents (№6 2013) | |
to russian | | |
STRUCTURAL MATERIALS, METAL SCIENCE
Graschenkov D. V., Schetanov B. V., Yefimochkin I. Yu., Shavnev A. A., Fedotov S. V. — Composite materials for heat-removing elements of power electronics
An analysis of copper-based metal-matrix composite materials used in manufacturing of heat-removing bases for power electronics is carried out. Different compositions and types of filling materials (fibres, fractions) are considered, major methods of obtainment of these materials and their basic heat-transfer properties are adduced.
Key words: metal-matrix composite materials, heat-removing base, power electronics, thermophysical properties of materials
TECHNOLOGIES AND EQUIPMENT FOR MACHINING, PHYSICOTECHNICAL PROCESSING, NON-CUTTING SHAPING
Lazarev D. Ye., Nasad T. G. — Upgrading surface finish quality at bore operations of deep bores
In this paper the method of vortex boring of precise holes was analyzed. There is periodically cutting during the processing of holes, similar to milling. The advantage of this method is the separation of chip into separate fragments, the formation of elemental chip. Also, the advantage of the vortex cutting is providing a high quality surface and high dimensional accuracy, low surface defects and low cutting tool deviation.
Key words: holes boring, surface quality, dimensional accuracy, boring tool
Yenek M. — Investigation of tribological properties of the 30ХГСA steel elements machined by the tool clad on the base of multicomponent metal nitride
The article presents results of studies of the wear process sample from hardened steel after machining cutting tool with carbide plates coated with metal nitride-based evaluation of surface roughness and tribological properties.
Key words: coated on the tool material, the process of turning, surface roughness, tribological characteristics
TOOLING PRODUCTION
Gourevich Yu. G., Ovcyannikov V. Ye., Frolov V. A. — A ferrite-pearlite grey cast iron burnisher with working surface alloyed by molybdenum
The technology of the superficial alloyage by molybdenum of ferrito-perlitny gray cast iron pieces be means of the oxidation of its matrix by molybdenum oxide with the subsequent quenching has been developed. Hardness after quenching is commensurable with hardness after quenching of malleable cast iron. Expediency of use of the strengthened samples is proved when manufacturing instruments for roughting for processing of color alloys.
Key words: gray cast iron, molybdenum oxide, superficial alloyage, quenching, blazing-off, instruments for roughting
Tabakov V. P., Saguitov D. I. — The multilayer wear-resistant coatings for lathe threading tool
The structural parameters and mechanical properties of wear-resistant coatings, the effect of multi-wear-resistant coating on the contact and thermal characteristics of the process of tapping, thermal and stress cutting wedge tool. Estimated efficiency of turning tools with threaded developed multilayer coatings.
Key words: thread, the thread-cutting tool, wearproof coatings, temperature, performance tool
Ardashev D. V., Akhlyustina V. V. — A test bed for investigating abrasive grain and work surface interaction in abrasive machining process
A construction of a microcutting test bench is offered, which allows promptly, without sizeable test costs carrying out investigations of tool and specimen interaction at high-speed processing techniques, i.e. grinding, HS turning, milling, et al.
Key words: microcutting, abrasive machining, sample and tool interaction
MACHINING-AND-ASSEMBLY PRODUCTION
Rozinov A. Ya., Beskrovny A. Yu. — Design-engineering improvement of assembly facilities with electromagnetic fastening intended for carrying out field connections of hull plating
Equations for calculation of holding power change of tractive flat-armature electromagnets and for magnetic induction determination in the air gap are given. Design-engineering features of round and rectangular electromagnets are considered.
Key words: tractive electromagnets, holding power, induction, air gap, pole area, magnetic flux, magnetic permeability
WELDING, RELATED PROCESSES AND TECHNOLOGY
Belalov I. R., Feofanov A. N. — Use of process equipment with parallel kinematics
Process equipment designed on basis of mechanisms with parallel kinematics is covered. Types of existing equipment, its merits and demerits are described.
Key words: equipment, parallel kinematics, ultrafast machining
SPECIAL TECHNOLOGIES
Andryushkin A. Yu. — Monodisperse liquid atomization by the supersonic gas-dynamic method
The organized analysis of the constructive schemes holey revolving device of the crushing (HRDC) and mode of the spraying by means of HRDC. The presented results of the calculation and experimental dependency data of the diameter of the drop not viscous and viscous liquid from angular velocity of the rotation HRDC. The efficient supersonic gas dynamic method is offered for crushing the viscous liquids. Using the supersonic flow of the gas allows vastly to lower the sizes of the drop, but in combination with HRDC, get alike dripped.
Key words: spraying, crushing, technological mixture, supersonic gas dynamic method
Bagaiskov Yu. S. — Composition development of a composite material of tubular filters for process liquid treatment
Filtering features of different process liquids, filter requirements are studied. A filtration facility is considered in which tubular ceramics-based filters are used. Dependences of filter materials’ permeability and durability indices on filter fineness, type and content of binding agent are analyzed.
Key words: composite material, filters, process liquid
TESTING AND DIAGNOSTICS METHODS IN ENGINEERING INDUSTRY
Yanguirov I. F. — Mathematical model of an electromagnetic quality analyzer of metal pipes’ manufacture
A mathematical model of the electromagnetic analyzer manufacturing quality metal pipes. We propose a mathematical model’s structures and electromagnetic analyzer manufacturing quality steel pipe, which has a high selectivity and resolution to technological defects of controlled items (eg oil and gas pipelines, welds, etc.).
Key words: model, metal pipe, the magnetic field, the conductivity, signal winding, analyzer
PROCESSES AND PRODUCTION AUTOMATION AND CONTROL, CAD SYSTEMS
Kolosov S. P., Seleznev M. Ye. — Application of data intelligent analysis technique as a function of decision support system for glass-pipes calibration automated lines in production
In publishers presents methods for automatic technical process, from functions caliber of glass-pipe, from workers of methods intellect analytics data, as monitoring bags.
Key words: technical of process, caliber, glass-pipe, medical glass, method of analysis
MATHEMATICAL MODELLING, CALCULUS OF APPROXIMATIONS AND SOFTWARE SYSTEMS
Lomayev V. I., Sagatelyan G. R. — Computer simulation of the parabolic reflector finishing operation
The article describes working surface finish of a radio antenna parabolic reflector made of a composite material. This operation is carried out on a specialized machine tool by using the method of fixed axes. A special computer program was developed: it allows to calculate the expected real shape of the processed surface depending on a variation of factors of the finishing process. The article suggests a classification of estimated deviations of the processed surface from sphericity. The required accuracy of the surface shape of a paraboloid of revolution is reached by neutralization of initial deviations which arise at forming of a reflector during the finishing process.
Key words: composite material, lapping, parabolic antenna, abrasive tool, tilt
STANDARDIZATION AND PRODUCT QUALITY CONTROL
Zmiyevsky V. I. — Assessment of the quality management system of granular and powder metallurgy production
An analysis of the present certification requirements of the quality management systems of granular and powder metallurgy production is given; suggestions on requirements fulfilment control by the certification bodies of the quality management systems as of exercising activities by them are offered.
Key words: granular and powder metallurgy, quality, conformance evaluation
PRODUCTION ORGANIZATION
Krasnopevtseva I. V. — IT as a growth factor of working efficiency at industrial enterprises
Necessity or information of industrial production with a view or increase of its efficiency is proved. The analysis of influence of information security of the enterprises on a labour productivity level is load. The basic problems, interfering universal introduction in manufacture of information technologies are revealed influence of the human factor on efficiency of use of information resources is noted.
Key words: industrial production, the enterprises of mechanical engineering, information resources, labour productivity, information potential of the staff
FOREIGN EXPERIENCE
Potapova G. S. — Review of the foreign journals
INFORMATION
Ivanov A. N. — The 11th International specialized exhibition “Cryogen-expo’2012”
Exhibitions in July—September, 2013